ZenotiHelp

Truncating hover labels on chart layout fields

ZTZenoti Docs Team Updated November 3, 2026 4 min readGuide

Field labels in Charting Templates layouts automatically shorten to fit within their column width, revealing the full text when you hover over or long-press a truncated label. This article explains how that behavior works and what to expect when form fields have long labels or required-field markers.

Audience: Providers and form administrators who build or review Charting Templates layouts in the form builder.


On this page


Before you begin

  • Your organization must have Charting Templates enabled. Contact your administrator if you cannot access charting layouts in the form builder.

  • You need the following permission to view and work with Charting Templates:

    Permission: View under AI Scribe charting templates in the Administrator section of the security role.

  • To modify a charting layout, you additionally need:

    Permission: Edit under AI Scribe charting templates in the Administrator section of the security role.

  • Truncating label behavior applies to fields rendered inside charting component layouts. It is not a configurable setting — the system applies it automatically based on the available column width.


How truncating labels work

When a field label is too long to display fully within its allocated column width, Zenoti renders it as a single-line label with an ellipsis (…) at the point where the text is cut off.

To see the complete label text:

  • On a desktop or laptop: Move the mouse pointer over the truncated label. After a short delay, a tooltip appears showing the full label text.
  • On a touch device: Long-press the truncated label. The tooltip appears after the same brief delay.

The tooltip disappears when you move away from the label or lift your finger.

Note: The hover delay is consistent across all fields in a charting layout. There is no way to adjust this delay through the form builder or any settings page.

What determines whether a label is truncated

The system compares the rendered width of the label text against the column width assigned to the field in the charting layout. Column width is set using the Column properties control on the Basic tab of the Columns component in the form builder. If the label text exceeds the available width at any column size (xs, s, m, l, or xl), the system truncates it and enables the hover tooltip automatically.

Tip: If a field label is truncating more than intended, consider widening the column using Column properties, or shortening the label text in the field definition.

Worked example: A field labeled "Pre-existing cardiovascular conditions" is placed in a small (s) column. At that width, the label renders as "Pre-existing cardio…". Hovering over it reveals the full label in a tooltip. Moving the column to medium (m) may allow the full label to display without truncation, depending on your screen resolution.


Required-field markers on truncated labels

When a field is marked as required, a red asterisk appears inline within the label text. Truncating label rendering preserves this asterisk even when the label is shortened.

This means:

  • If the asterisk falls within the visible portion of the label, it appears alongside the truncated text.
  • If the label is very short or the asterisk is the last visible character before the ellipsis, the asterisk still renders correctly before the cutoff point.
  • The tooltip that appears on hover always shows the complete label text, including the asterisk in its correct position.

Important: The red required-field asterisk is never hidden or removed by truncation. Guests and providers can always see that a field is required, regardless of how much of the label is visible.


Tips

  • Prioritize meaningful label beginnings. Because truncation cuts from the end of the label, place the most identifying words at the start. For example, use "Cardiovascular — pre-existing conditions" rather than "Pre-existing conditions — cardiovascular" so the key term stays visible even when truncated.
  • Test your layout at different column sizes. Use the Column properties control on the Columns component Basic tab to preview how labels appear at xs, s, m, l, and xl widths before publishing a form. Switch column sizes to confirm required-field asterisks remain visible at your target size.
  • Keep required-field labels short when using small columns. In a narrow column, a long required label may truncate before the asterisk is visible in the shortened text. Shortening the label or widening the column ensures the asterisk is always in the viewable area.

Troubleshooting

The tooltip does not appear when I hover over a truncated label.

The tooltip appears after a brief delay. If the tooltip is not appearing, confirm that the cursor is resting directly over the label text and not over an adjacent field or whitespace. On touch devices, try a firm long-press rather than a quick tap.

The label does not appear truncated even though it is long.

If the column is wide enough to display the full label, no truncation occurs and no tooltip is shown. Reduce the column width using Column properties on the Basic tab of the Columns component to reproduce the truncation behavior, or verify that the label text exceeds the current column width.

The required-field asterisk is not visible on a truncated label.

If the column is very narrow, the asterisk may appear at a position that falls within the ellipsis cutoff. Widen the column using Column properties, or shorten the label text so the asterisk falls within the visible portion. The tooltip always shows the full label including the asterisk, so hovering confirms the field is required even if the asterisk is not visible inline.


Was this article helpful?
Your feedback helps us improve our documentation.