Prerequisites & finishing services
Configure service prerequisites and finishing services to create structured service workflows and ensure proper service sequencing.
Audience: Administrators and managers who configure service catalog settings.
On this page
Before you begin
- You need the Edit permission under Services in the Administrator section to configure prerequisites and finishing services.
- Ensure all prerequisite services and finishing services are already created in your service catalog.
- Decide whether finishing services should use the same provider as the primary service or allow different providers.
Permission: Edit (under Services in the Administrator section) — required to save changes to service prerequisites and finishing service configuration.
Steps
Configure service prerequisites
Prerequisites ensure guests complete required services before booking certain advanced services.
- Navigate to Master data > Services.
- Select the service that requires prerequisites.
- Select the Prerequisites tab on the service details page.
- In the Prerequisite services section, select the services that must be completed before this service can be booked:
- Prerequisite Service — Choose one or more services from your catalog.
- Validity Days — Specify how recently (in days) the prerequisite must have been completed. For example, entering
60means the guest must have completed the prerequisite service within the last 60 days. - Order — Set the display order for each prerequisite in the list.
- Optionally, configure Prerequisite Equivalent services — these are alternate services that satisfy the prerequisite requirement in place of the primary prerequisite. Add them in the section below the prerequisite list.
- Select Save.
Note: During appointment booking, Zenoti validates prerequisite fulfillment and displays a warning when prerequisites are not met. The guest cannot proceed with booking until the prerequisite condition is satisfied or the warning is acknowledged, depending on your configuration.
Worked example: A chemical peel service requires guests to have completed a patch test within the last 60 days. Set Prerequisite Service to "Patch Test" and Validity Days to
60. If a guest attempts to book the chemical peel without a recent patch test on record, Zenoti displays a prerequisite warning at booking.
Set up finishing services
Finishing services are automatically appended after the primary service when an appointment is booked.
- On the same service details page, select the Finishing services tab.
- In the Associated Finishing Services section, configure the following:
- Finishing service — Select the service to automatically add after the primary service.
- Additional Service Time — Set the duration (in minutes) allocated for the finishing service.
- Same provider — Enable this option to ensure the finishing service uses the same provider as the primary service. Disable it to allow a different provider to deliver the finishing service.
- Select Save.
Important: Services defined as prerequisites of the primary service cannot also be defined as finishing services. Add-on services and parent variant services cannot be defined as finishing services.
Worked example: A deep-tissue massage service has a 10-minute cooling-down stretch as a finishing service. Set Finishing service to "Post-Massage Stretch", Additional Service Time to
10, and enable Same provider so the same provider completes both services without a handoff.
Test prerequisite validation
- Navigate to the Appointment Book and attempt to book the service that has prerequisites configured.
- If the guest has not completed the required prerequisite services within the validity period, Zenoti displays a warning message identifying which prerequisites are missing.
- Verify the warning includes details about which prerequisites are not met before proceeding.
Verify finishing service behavior
- Book an appointment for a service with a configured finishing service.
- Confirm the finishing service automatically appears in the appointment timeline immediately after the primary service.
- Check that the provider assignment follows your configuration — same provider if that option is enabled, or open to a different provider if it is disabled.
Tips
- Use prerequisites for advanced services that require foundational treatments, such as requiring a consultation before a chemical peel.
- Configure finishing services for treatments that benefit from immediate follow-up care, such as applying a soothing mask after an exfoliation.
- When setting finishing service duration, account for any transition time between the primary and finishing service.
- Consider guest experience when deciding whether to use the same provider for finishing services — some treatments benefit from continuity while others may work better with specialized providers.
- If a service category or tag is used to define finishing services, ensure none of the services in that category or tag are also defined as prerequisites of the primary service, as those will be excluded automatically.
Troubleshooting
The prerequisite warning does not appear during booking. Verify that the prerequisite service is saved correctly on the Prerequisites tab and that the Validity Days field contains a value greater than zero. If validity days is blank, the system may not enforce the time-range check. Also confirm the guest's appointment history does not already include a qualifying completion of the prerequisite service within the validity window.
The finishing service does not appear in the appointment timeline after booking. Check that the finishing service is saved on the Finishing services tab and that Additional Service Time is set to a value greater than zero. A finishing service with zero duration may not render visibly in the timeline. Also confirm the finishing service is active and associated with at least one center.
A service I want to use as a finishing service is not available in the selection list. Add-on services and parent variant services cannot be configured as finishing services — they are excluded from the selection list by design. If the service you want to use falls into either category, consider creating a standalone version of that service to use as the finishing service instead.