ZenotiHelp

Set up location groups

ZTZenoti Docs Team Updated September 4, 2026 3 min readGuide

Location groups let you create named groupings of centers within a zone. Once set up, you can use the Zone/Location groups filter in reports to analyze data for a specific subset of centers without scrolling through the full center list.

Audience: Organization administrators who manage multi-center operations.

Before you begin

Permission: Organization administrator access β€” these settings open for roles that carry organization-level administrator rights, such as the default Owner and Administrator roles. The role editor has no separate check box for this: the Organizations row in the Administrator section reads No applicable permissions.

Before creating location groups:

  • The Enable location groups organization setting must be enabled. This setting is org-level and applies to all centers.
  • You must have at least one zone configured. Each location group belongs to exactly one zone.
  • Confirm which centers belong to each group before creating β€” the Parent zone assigned to a group cannot be changed after the group is created.

Enable location groups

  1. Navigate to Configuration > Business details > Business setup > Features.
  2. Locate Enable location groups.
  3. Toggle it On.
  4. Click Save.

Once enabled, the location groups management page becomes available.


Scope and hierarchy

Location groups exist at two levels:

Level Description
Organization Location groups are created and managed at the organization level. All centers across all zones are accessible for group assignment.
Zone Each location group belongs to exactly one zone (its Parent zone). You cannot move a group to a different zone after creation.

A single center can belong to one location group per zone. Centers appear in the location groups filter in reports only if they are assigned to at least one group.


Create a location group

  1. Navigate to Configuration > Location groups.
  2. Click Add location group (or the equivalent create action).
  3. On the General tab, enter:
    • Name β€” A descriptive name for the group (for example, "West Coast Centers" or "Premium Locations").
    • Code β€” A short unique identifier for the group.
    • Parent zone β€” Select the zone this group belongs to. This cannot be changed after the group is saved.
  4. Click Next to proceed to the Centers tab.
  5. On the Centers tab, select the centers you want to include in this group.
  6. Click Save.

The location group is now active and available in report filters.


Edit an existing location group

You can update the name, code, and center membership of an existing location group. The Parent zone cannot be changed after creation.

  1. Navigate to Configuration > Location groups.
  2. Select the location group you want to edit.
  3. Update the Name, Code, or Centers as needed.
  4. Click Save.

Note: Adding or removing centers from a group takes effect immediately. Historical report data is not retroactively regrouped.


Use location groups in reports

Once location groups are set up, the Zone/Location groups filter appears in the following V2 reports:

  • Payroll report
  • Tips report
  • Attendance report
  • Royalty report
  • Cross Center Settlement report
  • Business KPI report

To use the filter:

  1. Open one of the reports listed above.
  2. In the filter panel, select Zone/Location groups.
  3. Choose the zone and then the location group to narrow results to the centers in that group.

This is especially useful for regional managers who want to compare performance across a defined subset of centers rather than viewing all centers or a single center at a time.


Tips

  • Plan your zone structure before creating location groups. Because the Parent zone is immutable after creation, reorganizing zones later requires deleting and re-creating affected groups.
  • Use a consistent naming convention for group codes β€” short, uppercase codes (for example, WC-01, NE-02) aid in report filtering and identification.
  • Location groups do not replace zones; they provide a finer-grained grouping within a zone. A zone can have multiple location groups, and a center appears under all groups it belongs to within that zone.
  • After enabling location groups, verify that the Zone/Location groups filter appears in your reports. If it does not appear, confirm the Enable location groups org setting is saved and that at least one group has centers assigned.

Was this article helpful?
Your feedback helps us improve our documentation.