Inventory Budget β Bulk Raise Budget Gate
Audience: Center admin, inventory manager
On this page
When you raise multiple purchase orders at once from the Inventory > Orders listing, Zenoti evaluates each selected order against the monthly inventory budget before committing the raise. If any order would push a center over its budget, the bulk raise either stops or warns you β depending on how budget enforcement is configured. This article explains what you see at each stage and how to respond.
Availability: Requires the Inventory budget feature to be active for your organization. Contact your Zenoti representative if the budget columns are not visible on the orders listing.
Before you begin
Purchase orders must be in Created status before they can be raised in bulk.
The Inventory budget feature must be enabled, and a monthly budget must be configured for the relevant centers. See Inventory Budgets β Budget Setup and Management Page.
Budget enforcement is set to either Warn or Block mode at the organization or center level. If you are unsure which mode applies, check Configuration > Inventory > Essentials > Inventory budget or ask your administrator.
You need the following permissions:
Permission: RAISE_ORDER β Required to raise purchase orders. Admin path: Configuration > Security > Security Roles > [your role] > Inventory > RAISE_ORDER
Steps
Select orders to raise in bulk
- Navigate to Inventory > Orders.
- Use the filters β Order type, Order status, Time period, and Vendor β to locate the purchase orders you want to raise.
- Select the checkbox next to each order you want to raise. All selected orders must be in Created status. If any selected order is in a different status, you will see the message: "Selected orders must be in created status."
- From the I want to... menu, select Raise or Raise & email.
Review the budget gate panel
After you initiate the bulk raise, Zenoti evaluates every selected order against the monthly inventory budget for each affected center and month. If any order would cause a budget threshold to be breached, the Inventory budget panel appears before the raise completes.
The panel lists each affected center and month in a table with the following columns:
| Column | Description |
|---|---|
| Center | The center whose budget would be affected |
| Month | The calendar month the budget applies to |
| Budget | The total monthly budget configured for this center |
| Committed | Spend already committed by previously raised orders |
| Reserved | Spend reserved by orders in Created status |
| Available | Remaining budget (Budget minus Committed minus Reserved) |
| Required | Additional spend that the selected orders would add |
| Orders | The specific order or orders contributing to the overage |
The message shown and the available actions depend on enforcement mode.
Respond to a Warn-mode panel
When enforcement is set to Warn, the panel displays:
"Some orders go over the inventory budget at the centers below. Do you want to continue?"
In Warn mode you can review the budget figures and choose to proceed. The panel accepts an optional override reason before you confirm.
- Review the Center, Available, and Required columns to understand which centers are over budget and by how much.
- If you want to continue despite the overage, enter an override reason in the provided field.
- Select the confirmation button to proceed. The bulk raise completes for all selected orders, and the override reason is recorded in the override log.
Worked example: Your organization has a $2,000 monthly budget for the Downtown center. Committed spend is $1,800 and the three orders you selected require $400 combined. Available balance is $200, and Required is $400 β an overage of $200. In Warn mode, you can enter "Vendor promotion β pre-approved by manager" as the override reason and continue.
Respond to a Block-mode panel
When enforcement is set to Block, the panel displays:
"Some orders go over the inventory budget at the centers below. Over-budget orders are blocked at these centers. Change the selection, or override with a reason."
In Block mode, orders that would exceed the budget cannot be raised unless you provide an authorized override reason.
Review the table to identify which orders and centers are over budget.
Choose one of the following actions:
- Override with a reason β Enter a reason in the override field and confirm. The over-budget orders are raised, and the override is logged.
- Change your selection β Close the panel, return to the orders listing, deselect the orders contributing to the overage, and re-initiate the bulk raise with a reduced selection.
Review the skipped-orders alert
If the bulk raise completes but one or more orders could not be raised because they exceeded the budget and no override was provided, you will see the following alert:
"These orders were not raised because they go over the inventory budget: {order list}"
The alert lists each order that was skipped. Orders not on this list were raised successfully. You can return to the listing, adjust quantities or center budgets, and re-attempt the raise for the skipped orders.
Tips
- Check available balance before selecting orders. The Available column on the budget management page shows remaining budget for each center and month. Selecting orders whose combined Required value fits within Available avoids the budget gate entirely.
- Use the Orders column in the panel. The Orders column identifies exactly which orders contribute to the overage for each center-month pair, making it straightforward to decide which orders to deselect if you want to avoid an override.
- Record meaningful override reasons. Override reasons are stored in the override log on the Budget setup page and are visible to administrators. Descriptive reasons β such as citing a vendor promotion or a pre-approved exception β make future audits easier.
- In Block mode, partial selection is valid. You do not need to cancel the entire bulk raise when some orders are over budget. Deselect only the problematic orders, raise the rest, and handle the over-budget orders separately after adjusting the budget or obtaining authorization.
- Warn mode still records the override. Even in Warn mode, any override reason you enter is logged. Treat it the same as a Block-mode override from an audit-trail perspective.
Troubleshooting
The budget gate panel does not appear, but I expected it to.
The panel only appears when the Inventory budget feature is active and a monthly budget has been configured for the affected center and month. If no budget is configured for a center, the gate is not evaluated for that center. Confirm that a budget amount appears on the Budget setup tab for the relevant center and month. See Inventory Budgets β Budget Setup and Management Page.
The skipped-orders alert lists orders I intended to raise.
This alert appears when Block mode prevented specific orders from being raised and no override was provided for them. To resolve: either increase the center's budget for the affected month on the Budget setup tab, reduce the quantities on the blocked orders, or re-initiate the raise with an override reason entered when the Block-mode panel appears.
I entered an override reason in Block mode, but the orders were still skipped.
The override reason field must be filled in before you select the confirmation button. If the field is left empty when you confirm, the system treats the action as declining the override and skips the over-budget orders. Return to the listing, re-select the skipped orders, and repeat the raise β entering the override reason before confirming.
Some orders in my selection were not in Created status and the bulk raise did not start.
The message "Selected orders must be in created status" appears when any selected order is in Raised, Updated, In transit, Partially delivered, or Delivered status. Return to the listing, deselect any orders that are not in Created status, and re-initiate the bulk raise.
I see "There are deleted orders in the selected list."
This message appears when a selected order has been deleted since the page loaded. Refresh the listing, remove the deleted order from your selection, and retry.