ZenotiHelp

Castle S1F2

ZTZenoti Docs Team Updated October 29, 2026 7 min readGuide

The Castle S1F2 is a payment terminal that connects to Zenoti for card-present transactions at the point of sale. This article covers device capabilities, how to connect the terminal to a Wi-Fi network, how to register it in Zenoti, and how to resolve common issues.

Audience: Front-desk staff and center administrators who set up and maintain payment terminals.


On this page


Before you begin

  • Your center must have an active payment processor configured in Zenoti.
  • You need access to Configuration to register terminals. If you do not have access, contact your organization administrator or Zenoti Support.
  • Have the device's serial number available before you begin registration.
  • A PIN is required to open the device's settings menu and join a Wi-Fi network. Contact your Castle device representative or refer to the Castle documentation for the current admin PIN. Do not enter this PIN in any public documentation.

Permission: You need access to Configuration > Payments > Process payments > Payment processor onboarding > Terminals to add a terminal. If you cannot navigate to this path, contact your organization administrator or Zenoti Support.


Device capabilities

The table below summarizes the Castle S1F2's key attributes so you can confirm the device meets your center's requirements before proceeding with setup.

Attribute Value
Connectivity Wi-Fi
Payment methods Chip (EMV), Contactless (NFC), Swipe (magnetic stripe)
On-device tip prompt No
Mirror mode No
PIN on device Yes (for settings menu and network join β€” refer to vendor documentation for the current value)
Firmware update mechanism On-device (see Update terminal firmware)
Supported regions Refer to your payment processor's regional availability documentation
Multiple terminals per center Yes
On-device admin PIN Not published; see the Castle S1F2 section on the admin PIN below

Connect to the network

The Castle S1F2 connects to Zenoti over Wi-Fi. You must join the terminal to your center's Wi-Fi network before you can register it in Zenoti.

Important: You need the device's admin PIN to access the settings menu. Never share or publish this PIN. Obtain it from the Castle documentation or your device account representative.

  1. Power on the Castle S1F2 by pressing the Power button on the device.
  2. When the device has started, navigate to the device settings menu by entering the admin PIN when prompted.
  3. Tap the Wi-Fi or network settings option on the terminal's touchscreen.
  4. Select your center's Wi-Fi network from the available list.
  5. Enter the Wi-Fi password using the on-screen keyboard and confirm.
  6. Wait for the device to display a connected status before proceeding.

Tip: Place the terminal close to the Wi-Fi access point during initial setup to ensure a stable connection. You can move it to its permanent position once registration is complete.


Register the terminal in Zenoti

After the terminal is connected to the network, register it in Zenoti so it appears as an available terminal at checkout.

  1. In Zenoti, go to Configuration > Payments > Process payments > Payment processor onboarding.
  2. Select Terminals.
  3. Select Add Terminal.
  4. Configure the following settings:
    • Terminal name β€” Enter a name that identifies this terminal at your center (for example, "Front desk β€” S1F2").
    • Serial number β€” Enter the serial number printed on the back of the device.
    • Center β€” Select the center where this terminal will be used.
  5. Select Save.
  6. The terminal appears in your terminals list. Confirm the status shows as connected or active before taking a payment.

Note: If you do not have access to Configuration > Payments > Process payments > Payment processor onboarding, contact your organization administrator or Zenoti Support to request the required access.


Update terminal firmware

Keep the device firmware up to date to ensure compatibility with Zenoti and your payment processor.

  1. Press the Power button to wake the device if it is in sleep mode.
  2. Navigate to the device settings menu by entering the admin PIN when prompted.
  3. Tap the firmware or software update option on the terminal's touchscreen.
  4. Follow the on-screen prompts to download and install any available updates.
  5. The device restarts automatically after the update completes.
  6. Once the device has restarted, confirm the terminal reconnects to Wi-Fi and appears as connected in Zenoti before resuming transactions.

Important: Do not power off the device or disconnect it from power during a firmware update. An interrupted update can leave the device in an unusable state.


Take a payment with this terminal

Once the terminal is registered and connected, it is available for selection at checkout.

For payment collection steps, see Payment processing.


Handle transaction failures

If a transaction does not complete successfully, use the guidance below to identify and resolve the issue.

Card declined

When a card is declined, the terminal displays a decline message and the transaction does not proceed.

  • Ask the guest to try a different card or payment method.
  • Verify the card has not expired and the guest is entering the correct PIN if prompted.
  • If repeated declines occur on multiple cards, check that the terminal is correctly registered in Zenoti and that the payment processor account is active.

Connectivity loss mid-transaction

If the terminal loses its Wi-Fi connection during a transaction, the transaction may time out or return an error.

  • Check that the device still shows a Wi-Fi connection on its screen.
  • If the connection has dropped, move the terminal closer to the access point and wait for it to reconnect, then retry the transaction.
  • Do not attempt to submit the same transaction twice before confirming whether the original was processed, to avoid duplicate charges.

Timeout errors

A timeout error occurs when the terminal or Zenoti does not receive a response within the expected window.

  • Common causes include a slow or unstable network connection, or the terminal being out of Wi-Fi range.
  • Move the terminal closer to the access point and retry the transaction.
  • If timeouts persist, try connecting the device to a different Wi-Fi network or a mobile hotspot to rule out a network-specific issue (see Keeps disconnecting below).

Tips

  • Assign a clear, location-specific name to each terminal (for example, "Station 1 β€” S1F2") so front-desk staff can identify it quickly at checkout.
  • Restart the terminal at the start of each business day if it has been idle overnight to ensure it has the latest connection to Zenoti.
  • Keep the device plugged in to power at the front desk. The Castle S1F2 can be used while charging β€” connect it using the USB-C cable supplied with the device or a compatible USB-C cable.

Troubleshooting

Keeps disconnecting

If the terminal repeatedly drops its Wi-Fi connection, work through the following checks in order:

  1. Check firmware β€” Verify the device firmware is up to date (see Update terminal firmware). Outdated firmware can cause unstable Wi-Fi behavior.
  2. Rule out the network β€” Try connecting the device to a different Wi-Fi network or a mobile hotspot. If the connection is stable on the alternate network, the issue is with your center's network configuration rather than the terminal.
  3. Confirm registration in Zenoti β€” Verify the terminal is correctly paired and registered in Zenoti under Configuration > Payments > Process payments > Payment processor onboarding > Terminals. A terminal that is not properly registered may appear to connect but fail to maintain a stable session.
  4. Check the SIM (if applicable) β€” If your device uses a SIM card for connectivity, confirm the SIM is active and has an active data plan with your carrier.

USB-C charging cable keeps failing

If the terminal is not charging or repeatedly loses charge:

  1. Try a different USB-C cable. If the terminal charges with the new cable, the original cable is at fault β€” replace it.
  2. If the device still does not charge after trying a different USB-C cable, contact Castle support or your device representative for hardware assessment.

Terminal not appearing in Zenoti

If the terminal does not appear in the terminals list after registration:

  • Confirm the serial number entered during registration matches the serial number on the device exactly.
  • Confirm the correct center was selected during registration.
  • Refresh the terminals page in Zenoti.
  • If the terminal still does not appear, contact Zenoti Support with the serial number and center name.

FAQ

Which Wi-Fi security types does the Castle S1F2 support?

Refer to the Castle S1F2 product documentation for the list of supported Wi-Fi security protocols. Zenoti communicates with the terminal over Wi-Fi regardless of the security type, provided the terminal and the Zenoti application can reach each other on the network.

Can a center use multiple S1F2 terminals?

Yes. You can register multiple terminals at the same center. Each terminal must be added separately under Configuration > Payments > Process payments > Payment processor onboarding > Terminals with a unique name and serial number.

What payment methods does the terminal accept?

The Castle S1F2 accepts chip (EMV insert), contactless (NFC tap), and magnetic stripe (swipe) payments. PIN entry on the device is supported for chip and contactless transactions where required by the card network or issuer.

Where do I find the admin PIN?

The admin PIN for the Castle S1F2 settings menu is not published in Zenoti documentation. Obtain it from the Castle device documentation provided with your hardware or contact your Castle account representative. Never share or display the admin PIN in public-facing materials.


Was this article helpful?
Your feedback helps us improve our documentation.