Verifone E285
The Verifone E285 (models e285 and e285p) is a compact payment terminal that connects to Zenoti through Adyen. This article explains how to add the terminal in Zenoti, pair it with an iPad, view reports on the device, and resolve common connection issues.
Audience: Front desk staff and administrators who set up and use Adyen-connected Verifone terminals.
Before you begin
Your organization must have Adyen configured as the payment processor. For general payment processor setup, see Set up a payment processor.
You need the following permission to add a terminal in Zenoti:
Permission: Export check box on the Export_Admin row of the Administrator section β required to download classic reports from the terminal reports screen. Admin path: Configuration > Security > Security Roles > [your role] > Administrator > Export_Admin
Have the terminal's serial number ready. The serial number is printed on the label on the back of the device.
The terminal must be powered on and connected to your network before you register it in Zenoti.
Device capabilities
The following table summarizes the key attributes of the Verifone E285.
| Attribute | Value |
|---|---|
| Processor | Adyen |
| Models covered | e285 and e285p |
| Connectivity | Wi-Fi |
| Payment methods | Chip, Contactless (NFC), Swipe |
| On-device tip prompt | Refer to your Adyen account configuration |
| Supported regions | All regions supported by Adyen β confirm availability with your Adyen account representative |
| Multiple terminals per center | Yes |
| Mirror mode | Confirm availability with Zenoti Support |
| Firmware update | Managed through Adyen; see Update terminal firmware |
| On-device admin PIN | Admin password set by your organization or the terminal vendor; Zenoti does not set or store it |
Connect to the network
The Verifone E285 connects to your network over Wi-Fi. It does not support Ethernet, so place it within reliable range of your access point.
The terminal and the iPad or POS device must be on the same network, and on the same band (2.4 GHz or 5 GHz). A guest network or a network that isolates devices can stop them from finding each other. For the full list of network requirements, see Network requirements.
Register the terminal in Zenoti
- Navigate to Configuration > Payments > Process payments > Payment processor onboarding > Terminals.
- Select Add to register a new terminal.
- Enter the serial number from the label on the back of the device.
- Select Save.
Note: If the terminal does not appear or fails to connect after registration, see Handle connection problems below, or refer to the connectivity article for network troubleshooting guidance: Set up a payment processor.
Pair the terminal with an iPad
- Power on the Verifone E285 and connect it to the same Wi-Fi network as the iPad.
- On the iPad, open Zenoti Mobile.
- Open the terminal settings within Zenoti Mobile and select the option to add a terminal.
- Select the E285 from the list of available terminals.
- When prompted, enter the pairing PIN displayed on the terminal screen.
Important: The pairing PIN is shown on the terminal screen at the time of pairing. It is not a fixed value β enter the PIN exactly as it appears on the device during the pairing flow.
Update terminal firmware
Firmware for the E285 is managed through Adyen. If you see the "Payment gateway not supported" message, compare the firmware version on the terminal with the version Adyen requires, and update it using the process in Adyen's terminal documentation. Contact your Adyen account representative if you are unsure which version applies.
Take a payment with this terminal
- In Zenoti, open the invoice at the Point of Sale and go to payment.
- Select the card payment method and the E285 terminal.
- The guest inserts, taps or swipes their card on the terminal.
- Wait for the approval on the terminal. The invoice updates in Zenoti when the payment completes.
For the full checkout flow, see Payment processing.
View reports on the terminal
The E285 can display transaction summaries and batch or settlement reports directly on the device.
On the terminal home screen, tap Menu or Admin.
When prompted, enter the admin password. The default is 1234, or the password your organization has configured.
Important: The admin password is set by your organization or by the terminal vendor. Zenoti does not set or store this password. Contact your organization administrator or your Adyen account representative if you do not know the password. Never share admin passwords in written communications.
Choose one of the following report types:
- Transaction Summary β shows totals for transactions processed in the current session.
- Batch Report β shows all transactions in the current open batch.
- Settlement Report β shows transactions that have been settled with Adyen.
Note: Report availability may vary based on your Adyen configuration. Contact your Adyen account representative if a report type is not available on your device.
Handle connection problems
If the terminal cannot connect or process payments, check the following before contacting Zenoti Support.
"Payment gateway not supported" message
This message typically indicates one or more of the following conditions. Check all three before escalating.
| Condition | What to check | Resolution |
|---|---|---|
| Terminal not correctly configured or paired | Verify the serial number in Zenoti matches the label on the back of the device; confirm pairing was completed | Re-register the terminal or repeat the pairing steps |
| Firmware is out of date | Check the firmware version on the terminal against the version required by Adyen | Update the terminal firmware using the process described in Adyen's terminal documentation |
| Payment processor not fully activated | Confirm Adyen is fully activated for your organization and center | Contact your Adyen account representative to verify activation status |
Important: Confirm all three conditions are checked before contacting Zenoti Support.
Handle transaction failures
Card declined
When a guest's card is declined, the terminal displays a decline message. Ask the guest to try a different card or payment method. The transaction does not close the invoice β return to the Point of Sale screen in Zenoti to select an alternative payment method.
For processing payments at the point of sale, see Payment processing.
Connectivity loss mid-transaction
If the terminal loses its Wi-Fi connection during a transaction:
- The terminal displays a connectivity error.
- Do not attempt to process the same transaction again until you confirm the original transaction did not complete.
- Reconnect the terminal to the Wi-Fi network.
- Check the Adyen portal or the transaction history in Zenoti to confirm the transaction status before retrying.
Timeout errors
Timeout errors occur when the terminal does not receive a response from Adyen within the expected window. Common causes include:
- Weak or intermittent Wi-Fi signal.
- Network firewall blocking Adyen endpoints.
To resolve, move the terminal closer to the Wi-Fi access point, confirm the network has connectivity to Adyen's endpoints, and retry the transaction.
Tips
- Keep the terminal on a stable Wi-Fi network. The e285 does not support Ethernet β place it within reliable range of your access point.
- Verify the serial number carefully when registering. A transposed digit is the most common cause of registration failures.
- When pairing with an iPad, complete the pairing process without navigating away from Zenoti Mobile. Switching apps during pairing may interrupt the PIN exchange and require you to restart the process.
- If you operate multiple E285 terminals in the same center, register each terminal separately using its unique serial number.
Troubleshooting
| Symptom | Likely cause | Resolution |
|---|---|---|
| Terminal does not appear in the terminal list after registration | Serial number entered incorrectly | Remove the registration and re-enter the serial number exactly as printed on the back label |
| Pairing PIN entry fails | Terminal and iPad are on different Wi-Fi networks | Confirm both devices are connected to the same network, then restart the pairing process |
| "Payment gateway not supported" message at checkout | Terminal not paired, firmware outdated, or Adyen not fully activated | Follow the steps in Handle connection problems above |
FAQ
- How do I add the E285 card reader?
- How do I pair an iPad with the E285?
- How do I open the Reports menu on the E285?
- Where do I buy an E285?
How do I add the E285 card reader?
Go to Configuration > Payments > Process payments > Payment processor onboarding > Terminals, select Add, enter the serial number printed on the back of the device and select Save. See Register the terminal in Zenoti.
How do I pair an iPad with the E285?
Put the terminal and the iPad on the same Wi-Fi network, open Zenoti Mobile, add the terminal in the terminal settings, select the E285 and enter the pairing PIN shown on the terminal screen. See Pair the terminal with an iPad.
How do I open the Reports menu on the E285?
On the terminal home screen, tap Menu or Admin, enter the admin password and choose a report. See View reports on the terminal.
Where do I buy an E285?
Order terminals through the Zenoti Payments device ordering page. See Order, replace and return terminals.