Configure Gantner access control
Gantner integrates Zenoti with Gantner access-control hardware (locker terminals, turnstiles, entry gates, RFID wristbands). Gantner devices provisioned for a center are mapped to room categories, and access decisions follow the guest's membershipss that grant access. At run time, a guest presenting a Gantner band or card at a reader is verified against the membership-to-room rules and the gate opens or stays closed.
Note: Gantner is an on-premise hardware integration. The deployment model is different from every other fitness partner in this category — your facility owns and operates the Gantner controllers and readers, and the access decision is made by Zenoti against the access rules you configure here.
On this page
- Before you begin
- External-system prerequisites (Gantner hardware)
- Network requirements
- Enable Gantner at the organization level
- Map devices to rooms at the center
- How access control uses the mapping
- Verify the integration
- What to configure next
- Tips
- Troubleshooting
Before you begin
Permission: You need organization administrator access to enable Gantner, and center access to map devices at a center.
- Gantner hardware must be physically installed, powered, and on your facility network.
- Your Gantner installer has commissioned the devices through Gantner's own tooling before Zenoti knows about them. Zenoti does not commission hardware.
- You need the list of devices Zenoti has provisioned for each center; if a device is missing from the Device dropdown, contact Zenoti Support with the installer's device details.
- Memberships that will grant access must already exist in Zenoti.
External-system prerequisites (Gantner hardware)
Complete these on the Gantner side before registering devices in Zenoti. Gantner's installer portal layout varies by hardware generation and software version — refer to your Gantner installer or Gantner's own documentation for version-specific paths.
- Commission each device through Gantner's installer tooling. This assigns the device its serial number, article number, firmware version, and network identity.
- Record the device inventory for Zenoti Support, which provisions the devices for your centers:
- Serial number (unique per device).
- Article number (Gantner model article code).
- Device model (human-readable model name).
- Firmware version and hardware version.
- Intended physical location (which room / locker bank / entry gate the device controls).
- Confirm guest credentials (wristbands or cards) are provisioned with your installer.
- Agree on the maintenance contact between your facility and your Gantner installer. Firmware updates and hardware replacement are the installer's responsibility.
Network requirements
Gantner is on-premise. Zenoti and your Gantner deployment need reliable connectivity for access decisions to resolve in real time.
| Direction | Purpose | Protocol / port | What to whitelist |
|---|---|---|---|
| Gantner controller -> Zenoti | Access-check requests (device reads a band, asks Zenoti whether to open). | HTTPS / 443 | Outbound from the Gantner controller to Zenoti's public API domain. Work with your network team and your Gantner installer to whitelist the domain Zenoti provides during setup. Plain HTTP is not supported. |
| Zenoti -> Gantner | None. Zenoti does not initiate connections to the on-premise controller. | n/a | No inbound action on the facility network. |
If outbound HTTPS from the on-premise controller is blocked, the device cannot query Zenoti and access is not granted until connectivity is restored.
Enable Gantner at the organization level
- Navigate to Configuration > Integrations > Integration settings and expand Gantner. The accordion has one Configuration panel.
- Select Enable Gantner.
- Select Save inside the panel.
Until this checkbox is selected, the center panel shows only the message Gantner is not enabled at Organization level.
Map devices to rooms at the center
Gantner devices are provisioned for your centers by Zenoti as part of onboarding; the center panel lists the devices that exist for the center and lets you attach each one to a room category.
- Select the center in the center selector, then navigate to Configuration > Integrations > Integration Settings and expand GANTNER.
- In Configuration, each mapping is a pair of dropdowns: Device 1 and Room 1, Device 2 and Room 2, and so on. Pick the device, then the room category it controls.
- To add another pair, select Add another device and room category.
- Select Save.
A device can be mapped to one room category, and a room category to one device; the page tells you when a selection is already taken. To let two readers control the same area, ask Zenoti to provision each reader as its own device and map them to the same room category.
How access control uses the mapping
When a guest presents a Gantner credential at a device, Gantner checks with Zenoti whether the guest may enter the room category mapped to that device. Zenoti bases the answer on the guest's memberships, so the memberships that grant access must exist before you map devices.
Verify the integration
- Confirm Enable Gantner is selected at organization scope.
- At the center, confirm every device in use appears in a Device dropdown and is mapped to the correct room category.
- Present a credential at a mapped device and confirm the expected result with your Gantner installer.
What to configure next
Required:
- Continue issuing Gantner bands to enrolled members as part of your membership onboarding.
Recommended:
- Monitor integration health and metrics — add Gantner to your integration health dashboard.
- Enable BILT, Gympass, and FitReserve — for corporate-wellness marketplaces if applicable.
Tips
- Map every device before go-live; an unmapped device cannot be checked against a room category.
- Keep room categories aligned with how you sell memberships, so the mapping and the membership rules describe the same areas.
- After any facility network change, test one mapped device with your installer.
Troubleshooting
| Symptom | Likely cause | Resolution |
|---|---|---|
| The center GANTNER panel shows Gantner is not enabled at Organization level. | Enable Gantner is not selected at organization scope. | Select it under Configuration > Integrations > Integration settings > Gantner and save. |
| A device is not listed in the Device dropdown. | The device has not been provisioned for this center. | Contact Zenoti Support with the device details from your installer. |
| The page rejects a room or device selection. | That room category or device is already used in another pair. | Pick a different room category or device; each can appear in only one pair. |
| Access is denied at a mapped device. | The guest has no membership that grants access to that room category, or the controller cannot reach Zenoti. | Check the guest's memberships and the mapping; confirm outbound HTTPS from the controller. |