Verifone P400 Plus
The Verifone P400 Plus is a countertop card-reader terminal that connects to Zenoti through Stripe Connect. It accepts chip, contactless (NFC), swipe, and PIN-entry payments and prompts the guest for a tip on the device. Use this article to set up a P400 Plus, register it in Zenoti, update its firmware, and take payments.
Audience: Organization administrators and center managers who set up payment hardware, and front-desk staff who use the terminal at point of sale.
On this page
- Before you begin
- Device capabilities
- What's in the box
- Connect to the network
- Register the terminal in Zenoti
- Update terminal firmware
- Take a payment with this terminal
- Tips
- Troubleshooting
- FAQ
- Related articles
Before you begin
- Permission. You need administrator access to your Zenoti organization (Configuration > Payments > Process payments > Payment processor onboarding). Front-desk staff who only need to take payments do not need admin access β terminal selection and card collection happen on the regular Point of Sale (POS) screen.
- Processor. Stripe Connect must already be set up for your organization. See Set up a payment processor and Configure payment terminals and card readers for the broader Stripe Connect onboarding walkthrough. The P400 Plus uses Stripe Connect β it does not work with Adyen, FreedomPay, or any other Zenoti payment processor.
- Network. The center must allow outbound HTTPS (port 443) traffic to Stripe's terminal API endpoints. The P400 Plus reaches Stripe directly over the center's Wi-Fi or Ethernet β see Network requirements for Stripe terminals for the exact host list to allowlist on a restrictive firewall.
- Hardware. The P400 Plus, its connector cable, the Verifone power adapter, and (for Ethernet) an RJ-45 network cable. Do not substitute a generic USB power supply β the terminal expects the Verifone-branded adapter.
- Region. Verifone P400 Plus is available in every Stripe Connect region Zenoti supports: United States, Canada, United Kingdom, Australia, and the United Arab Emirates. Confirm device-region eligibility in Stripe's terminal hardware catalogue before ordering β Stripe ships region-locked SKUs.
Device capabilities
| Attribute | Value |
|---|---|
| Processor | Stripe Connect |
| Connectivity | Wi-Fi (primary); Ethernet (alternative). No Bluetooth. |
| Payment methods | Chip (EMV insert), Contactless (NFC tap, including mobile wallets), Swipe (magnetic stripe), PIN entry. |
| On-device tip prompt | Yes. Tip support is enabled per terminal in the Zenoti terminal settings. |
| Mirror mode | Not supported. Mirror mode is a Stripe iPad/WisePOS E pattern; P400 Plus is a standalone countertop device. |
| Supported regions | All Stripe Connect regions: United States, Canada, United Kingdom, Australia, United Arab Emirates. |
| Multiple terminals per center | Yes. A center can have multiple terminals; one is marked default in Zenoti. Front-desk staff can switch to a different terminal at the POS payment screen. |
| Firmware update mechanism | Manual via on-device admin menu (see Update terminal firmware). Not over-the-air. |
| On-device admin PIN | Vendor-published Verifone admin code required for the firmware-update menu. See vendor documentation or contact your account representative for the current value. |
| Device identifier in Zenoti | Registration Code (not a serial number β see Register the terminal in Zenoti). |
What's in the box
The P400 Plus ships with the device, a connector cable that plugs into the back of the terminal under the latch cover, and a Verifone power adapter. Order an RJ-45 network cable separately if the center will use Ethernet instead of Wi-Fi. The same connector cable is used for both Wi-Fi and Ethernet setups β the network choice changes only how the connector cable's network port is used (left empty for Wi-Fi, plugged into your network switch for Ethernet).
Connect to the network
You will physically attach the cable once and then choose either Wi-Fi or Ethernet. The hardware steps are identical for both β only the on-device menu choices differ.
Attach the cable
- Place the terminal screen-down on a soft surface so you can access the latch on the back of the device.
- Slide the latch open and lift the cover off.
- Plug the connector cable into the recessed port under the cover, then refit the cover and slide the latch closed.
- Plug the Verifone power adapter into the connector cable's power port (labelled with a power icon, sometimes called the RS232 port on the cable). The terminal powers on automatically and shows the Verifone logo, then the home screen β the screen that displays the Zenoti logo with no menu bar across the bottom.
Wi-Fi (recommended)
- On the home screen, swipe the screen down to reveal the status bar, then tap the gear icon to open Settings.
- Tap Wi-Fi. The terminal scans for nearby networks.
- Tap your Wi-Fi network name in the list.
- Enter the Wi-Fi password using the on-screen keyboard, then tap Connect. The terminal connects and the status bar shows a Wi-Fi signal icon.
- Press the red X button three times to return to the Welcome screen β the screen that displays the Zenoti logo with no menu bar.
Note: If the device has been set up before and you are switching networks (after a router change, password rotation, or moving the device to a new location), the Settings menu requires the on-device admin PIN. Enter the admin PIN when prompted, then continue with the Wi-Fi steps above. The PIN is a vendor-published Verifone code β refer to Verifone's documentation or your account representative for the current value.
Wi-Fi recovery: forget and re-add a network
If the terminal was working before but stopped connecting after a router change, password rotation, or a move to a new location, use the following route to forget the saved network and re-add it.
Tip: If you are unsure whether a router problem or the terminal itself is the cause, connect the terminal to a mobile hotspot. If the terminal connects successfully, the issue is with the center's router or network configuration, not with the device.
- Open Settings (gear icon on the home screen status bar). The Settings menu requires the admin PIN β enter the vendor-published admin code when prompted.
- Tap Network > Wi-Fi.
- Tap Network Forget, then confirm the prompt to forget the saved network.
- Tap Network > Wi-Fi > Add Network. Select your network from the list, enter the current password, then tap Connect.
- Verify that both the Wi-Fi icon and the cloud icon appear in the status bar before retrying a payment.
Ethernet (alternative)
Use Ethernet if your center's network policy requires wired connections (some PCI environments and franchise IT policies do), if the Wi-Fi signal at the terminal location is weak, or if firmware updates over Wi-Fi consistently fail. Otherwise, Wi-Fi is simpler and is the path the rest of this guide assumes.
- Plug an RJ-45 network cable into the network port on the connector cable (next to the power port) and into a free port on your network switch.
- On the home screen, open Settings as in the Wi-Fi steps. Tap Ethernet.
- Confirm the terminal shows a Connected status and an IP address. If the network requires a static IP, tap IP Settings and enter the values your network team provides; otherwise leave DHCP enabled.
Register the terminal in Zenoti
The P400 Plus is added to Zenoti by Registration Code, not by serial number. The registration code is a short alphanumeric string the device generates on demand and that Zenoti exchanges with Stripe to pair the terminal to your processor account.
Tip β replacing a device: When you replace a P400 Plus with a new unit, add the new terminal in Zenoti first using its Registration Code, verify that payments succeed on the new device, and then delete the old terminal entry. This order prevents a service gap: if you delete the old entry first, there is a window where no default terminal is active at the center.
- On the terminal β from the home screen, enter the key sequence
0-7-1-3-9to display the Registration Code. The code appears on the terminal screen as a string of letters and digits (for example,quick-brown-fox). - In Zenoti β go to Configuration > Payments > Process payments > Payment processor onboarding. Under Payment Processors, open the Stripe processor row (Setup for a processor that is not configured yet, Change for one that is) and select the Terminals tab.
- Add a terminal.
- Set Device Model to Verifone P400 Plus. The Registration Code field appears (the field label changes based on the selected device β for BBPOS Chipper 2X BT and Stripe Reader M2 the field is labelled Serial Number instead).
- Enter the Registration Code from step 1 into the Registration Code field. Give the terminal a friendly name (for example, "Front desk 1") so staff can identify it at the POS.
- If this is the first or only terminal for the center, mark it Default. Otherwise leave Default cleared β staff can pick this terminal at the POS as needed.
- Save. Zenoti contacts Stripe to register the device. The terminal status changes to Active within a few seconds.
Note: The Registration Code is single-use and expires shortly after it appears on the device. If registration fails, regenerate a fresh code with
0-7-1-3-9and retry.
Note: In some Zenoti configurations the add-terminal form asks for the Terminal Name and a Serial Number instead of a Registration Code. If so, enter the serial number printed on the label on the back of the device and select Add. Use whichever field the form shows after you pick the device model.
To bring a new P400 Plus online on the device itself:
- Connect to power. Open the back cover, connect the dongle cable and close the cover. Turn on the terminal. The display cycles on and off a few times during startup.
- Connect to the internet over Wi-Fi or Ethernet.
- Board the terminal. Select Board the Terminal, select your store and confirm.
Update terminal firmware
The P400 Plus must be on current firmware before on-device tip prompts and signature collection will work β a terminal restart on its own does not pick up firmware. Run this update once when you first board the device, and again whenever Stripe or Verifone announces a required update.
Important: A firmware update takes 30β40 minutes and blocks all card transactions on this terminal for the duration of the update. Do not run the update during peak hours. Plan to: (1) take payments on an alternative terminal at the same center while the update runs, (2) collect cards manually (Take Payment without a terminal) for guests checking out during the window, or (3) schedule the update before opening or after closing. The terminal cannot be cancelled mid-update without risking a corrupt firmware state.
- On the home screen, press 9 and the green Enter button. The admin-mode prompt appears.
- Enter the admin PIN and press the green Enter button. The admin PIN is a vendor-published Verifone code β refer to Verifone's documentation or your account representative for the current value.
- In the admin menu, select Config.
- Select Update. The terminal downloads and applies the latest firmware over its network connection. Do not unplug the device during the update β it takes 30β40 minutes.
- When the terminal returns to the home screen, the update is complete. Take a small test transaction to confirm tip prompts now display correctly.
Note: If you are still in the Admin Menu from a previous step (for example you opened it to check the Wi-Fi status), skip the key sequence and PIN re-entry β the menu is already open. The Config and Update items are available directly.
Take a payment with this terminal
The P400 Plus uses the same point-of-sale flow as every other Zenoti card terminal. Open the guest's invoice, choose Card as the payment method, and the cashier-facing payment screen pairs to the terminal automatically. The cashier can switch to a different terminal from a dropdown if the center has more than one. The guest then inserts, taps, or swipes their card on the P400 Plus and confirms the tip on the device.
For the full POS payment workflow β including how to handle declined cards, tip configuration, refunds, and partial captures β see Close invoices and collect payments.
Tips
- Mark one terminal as default per center. Front-desk staff don't have to pick a terminal at every transaction β only when the default isn't the one they want to use right now.
- Keep the Verifone power adapter with the terminal. A generic USB-C power supply may underpower the device and cause it to reboot mid-transaction.
- Run the firmware update right after boarding. Tip prompts and signature collection silently fail until the firmware is current β easier to fix on day one than after the first guest complaint.
- Note the friendly name on the device. A small label that matches the terminal name in Zenoti (for example, "Front desk 1") prevents staff from picking the wrong terminal at the POS.
- Re-register after a factory reset. A factory reset invalidates the existing registration. Re-run the
0-7-1-3-9sequence and add the new code in Configuration > Payments > Process payments > Payment processor onboarding, Stripe processor row, Terminals tab. - Use a mobile hotspot to isolate router problems. If you are not sure whether a network issue is with the center's router or with the terminal itself, connect the P400 Plus to a mobile hotspot. If it connects successfully, the problem is with the center's router or firewall, not with the device.
Troubleshooting
If a payment fails, classify the cause before running any fix steps. Different symptoms have different causes β running every fix in order wastes time and can briefly take the terminal out of service for a problem that wasn't on the device. POI in error messages stands for Point of Interaction (the payment terminal itself).
Identify the cause first
| Symptom on the terminal or POS | Likely cause class | Where to look first |
|---|---|---|
| "No such reader" / "Reader is currently offline" / "Failed to process payment. Timed out waiting for response from POI" | Connectivity (network or device) β the terminal can't be reached or doesn't respond | Network and connectivity fixes below |
| "Transaction declined" / "The transaction was declined by the issuer. Use a different card." | Issuer decline β the cardholder's bank rejected the charge; the terminal and Zenoti are working correctly | Ask the guest for a different card. Do not run terminal-side fixes; they will not help. |
| "Cannot process this transaction" with no specific error code, OR the transaction never reaches the terminal at all | Configuration / mapping β the terminal is not the active default for the center, the Registration Code does not match the device, or Stripe Connect onboarding is incomplete | Configuration fixes below |
| All terminals at all centers fail at the same time | Service or Zenoti outage β not a center-side issue | Check the Zenoti Payments status page for an active incident. Do not run terminal-side fixes. |
| "Payment was not processed as the system just completed a pending transaction" | Transient race with another in-flight transaction | Wait 30 seconds, retry the same payment from the POS. If it persists, reboot the terminal (see Reboot the terminal). |
Network and connectivity fixes
Run these in order. The earlier steps fix the most common causes the fastest. A countertop Verifone P400 Plus is mains-powered, so the legacy "check the battery" step does not apply unless the wall outlet, power strip, or adapter has actually failed β start with the network checks below.
1. Check the Wi-Fi and cloud icons on the home screen
Swipe the terminal screen down to reveal the status bar. You should see a Wi-Fi signal icon and a cloud icon (the cloud means the device has reached Stripe). If either icon is missing or has a strikethrough:
- Wi-Fi icon missing: the terminal is not on Wi-Fi. Open Settings (gear icon), tap Wi-Fi, and reconnect to your network. See Wi-Fi (recommended).
- Cloud icon missing: the terminal is on Wi-Fi but cannot reach Stripe. Check the center's outbound firewall β Stripe terminal API hosts must be allowlisted on port 443.
The appearance of both the Wi-Fi and cloud icons on the status bar is the signal that the device is connected and ready to process payments. Do not attempt a transaction until both icons are visible.
2. Reboot the terminal
A reboot fixes more terminal-side issues than any other single step on a P400 Plus. There are two ways to do it, and the menu route is preferred because it does not depend on which firmware revision the device is running.
From the admin menu (preferred):
- On the keypad, press 9 and the green Enter button.
- Enter the admin PIN and press the green Enter button. The admin PIN is a vendor-published Verifone code β refer to Verifone's documentation or your account representative for the current value.
- From the admin menu, select Reboot.
By the power button: hold down the power button (combined with the green Enter on some firmware revisions) until the device powers off, then press the power button to power it back on.
Either way, wait until both the Wi-Fi icon and the cloud icon appear on the status bar before retrying the payment. Those two icons together confirm the device is connected and ready.
3. Check the power adapter and outlet (if the terminal is dead)
If the screen is blank or the terminal cycles on and off:
- Confirm the Verifone power adapter is plugged into the connector cable's power port (not the network port) and that the wall outlet is live.
- Swap the power adapter for a known-good Verifone P400 Plus adapter from another center if you have one β generic USB power supplies do not deliver the correct current and can cause the terminal to reboot mid-transaction.
4. Re-seat or replace the Ethernet cable (Ethernet centers only)
If the center uses Ethernet (not Wi-Fi):
- Confirm the RJ-45 cable is fully plugged into the network port on the connector cable and into a live port on the network switch.
- Check the link-light on the switch port. If the light is off, swap to a different switch port.
5. Reconnect to Wi-Fi (if you've moved the terminal or rotated the password)
If the terminal was working before but stopped after a router change, password rotation, or moving to a new location, follow the Wi-Fi recovery steps β forget the saved network and re-add it using Network > Wi-Fi > Network Forget (confirm), then Network > Wi-Fi > Add Network. See Wi-Fi recovery: forget and re-add a network for the full procedure.
Tip: To rule out a router problem, connect the P400 Plus to a mobile hotspot. If the terminal connects and processes a test transaction successfully, the center's router or firewall configuration is the cause β not the device.
6. Run a firmware update (last resort, blocks transactions)
Important: Run this only after the steps above have all failed and you have an alternative terminal or are outside business hours. The update takes 30β40 minutes and blocks all card transactions on this terminal for the duration. See Update terminal firmware for the full procedure and operational planning advice.
Configuration fixes
- Registration Code in Zenoti doesn't match what the device shows. The code is generated fresh each time you press
0-7-1-3-9and expires after a short window. Always copy the code that's currently on the screen, not one from an earlier attempt. If you accidentally generate a code on the wrong device, walk through0-7-1-3-9again on the correct device. See Register the terminal in Zenoti. - Terminal is registered but not selected at the POS. A center can have multiple terminals. The cashier sees a terminal dropdown on the POS payment screen β if the wrong terminal is the default, switch the dropdown selection or change the default in Configuration > Payments > Process payments > Payment processor onboarding > Stripe > Terminals.
- Stripe Connect onboarding is incomplete. If Stripe Connect onboarding has not finished (KYC pending, bank account not linked, identity verification outstanding), Stripe rejects every transaction even if the terminal connects. Check Configuration > Payments > Process payments > Payment processor onboarding > Stripe for any outstanding onboarding step. The error in this case is generic ("Cannot process this transaction") rather than terminal-specific.
Other terminal issues
- The terminal cannot find any Wi-Fi network. Move the terminal closer to the router; the P400 Plus has a smaller antenna than a phone and is sensitive to walls and metal furniture. Confirm the Wi-Fi network is on the 2.4 GHz band β the P400 Plus does not support 5 GHz-only networks.
- Tip prompts do not appear on the terminal. Run the firmware update from Update terminal firmware. Tips silently fail on out-of-date firmware. After the update, also confirm tip support is enabled for this specific terminal in Configuration > Payments > Process payments > Payment processor onboarding > Stripe > Terminals β tip support is a per-terminal flag, not an organization-wide setting.
- A transaction is in progress and the cashier needs to cancel. Either tap the on-screen Cancel button on the cashier's POS screen, or press the red X button on the terminal. If the device shows "Transaction in progress" and neither button responds, wait β Stripe holds the cancel until the network round-trip completes.
Handle transaction failures
The following covers the most common failure scenarios and how to recover from each.
| Failure type | What the cashier sees | Recovery steps |
|---|---|---|
| Card declined | "Transaction declined" or "The transaction was declined by the issuer. Use a different card." | Ask the guest for a different card. The terminal is working correctly β this is a bank decision. Do not reboot the terminal or re-register it. |
| Connectivity loss mid-transaction (Wi-Fi) | "Failed to process payment. Failed to send message to POI. There may be a network issue or it may not have the websocket connected" or "Timed out waiting for response from POI" | Check the Wi-Fi and cloud icons on the status bar. If either is missing, reconnect the terminal to Wi-Fi (see Wi-Fi recovery), wait for both icons to appear, then retry. If the network is stable, reboot the terminal from the admin menu (press 9 + green Enter, enter the admin PIN, select Reboot); wait for the Wi-Fi and cloud icons to return before retrying. |
| Connectivity loss mid-transaction (Ethernet) | Same "Timed out" or "network issue" messages as Wi-Fi loss | Re-seat the RJ-45 cable at both the connector cable and the network switch. Check the switch port link-light. Once the link is restored, retry the payment. |
| Timeout error | "This transaction has timed out please try the purchase again" | The most common causes are a slow network, the guest taking too long on the tip screen, or a Stripe-side delay. Wait 30 seconds, then retry from the POS. If the error recurs consistently, reboot the terminal and check the Wi-Fi signal strength at the terminal's physical location. |
| In-flight transaction cannot be cancelled | Terminal shows "Transaction in progress" and does not respond to the Cancel button | Wait β Stripe holds the cancel until the network round-trip completes. Do not unplug the terminal. If the terminal is unresponsive for more than two minutes, reboot using the admin menu (press 9 + green Enter, enter the admin PIN, select Reboot). Check the Stripe payment dashboard or Zenoti Payment Dashboard to confirm whether the charge completed before retrying. |
If the problem persists
If you have run the connectivity steps in order, confirmed the configuration, and the terminal still cannot collect a payment:
- Take the payment another way. Switch to an alternative terminal at the same center (the cashier dropdown on the POS payment screen lists every active terminal). If no alternative is available, use Take Payment without a terminal to enter the card manually for this transaction β this keeps the guest moving while you continue diagnosing.
- Capture diagnostic detail. Note the exact error string the terminal or POS displayed, the time of the failure, and the affected terminal's Registration Code.
- Contact Zenoti Support. Open a support ticket and include the diagnostic detail from step 2 plus the Stripe Location ID for the center (visible in Configuration > Payments > Process payments > Payment processor onboarding, Stripe processor row). For multi-terminal organizations, also confirm whether the issue is isolated to one terminal or affects every terminal at the center.
FAQ
- Which regions support the Verifone P400 Plus? All Stripe Connect regions Zenoti supports: United States, Canada, United Kingdom, Australia, United Arab Emirates. Stripe ships region-locked SKUs, so confirm the device's region matches the center's Stripe Connect account before ordering.
- Does the P400 Plus support contactless and PIN entry? Yes. The P400 Plus accepts chip insert, contactless tap (including mobile wallets), magnetic-stripe swipe, and on-device PIN entry. Tip support is enabled per terminal in the terminal settings.
- Can a center use more than one P400 Plus? Yes. Add each terminal in Configuration > Payments > Process payments > Payment processor onboarding, Stripe processor row, Terminals tab, and mark one as the center's default. Front-desk staff can pick a non-default terminal at the POS payment screen.
- What is the on-device admin PIN, and who needs it? The admin PIN is a vendor-published Verifone code required for the firmware-update and network-settings menus. Refer to Verifone's official documentation or your account representative for the current value. Center staff who run firmware updates or change Wi-Fi settings need the PIN; staff who only take payments do not.
- Does this terminal work with Adyen? No. The P400 Plus is a Stripe Connect terminal in Zenoti. Adyen supports a different set of Verifone models (e285, V400m, and others). If your organization uses Adyen, work with your Adyen account manager to source a supported model.
- How do I retrieve the Registration Code if I've already added the terminal in Zenoti and need to re-add it? Re-running
0-7-1-3-9on the device generates a fresh Registration Code at any time. Use the new code to add the terminal again β the previous registration is automatically released by Stripe when a new one succeeds. - What if the terminal can connect to my network but not to Zenoti or Stripe? This is almost always an outbound-firewall issue. Allowlist Stripe's terminal API hosts on the center's network β see Network requirements for Stripe terminals for the exact host list. Adyen's IP/domain documentation does not apply to this device.
- How do I replace a P400 Plus with a new unit without interrupting payments? Add the new terminal in Zenoti first β use the
0-7-1-3-9sequence on the new device to get its Registration Code, then add it in Configuration > Payments > Process payments > Payment processor onboarding, Stripe processor row, Terminals tab. Confirm payments work on the new device, then delete the old terminal entry. Adding the new device before removing the old one ensures the center always has at least one active terminal.