ZenotiHelp

Configure payment terminals and card readers

ZTZenoti Docs Team Updated October 30, 2026 22 min readHow-to

Zenoti supports several Stripe terminal card readers for in-person payment collection. This article covers setup, configuration, and troubleshooting for each supported device: BBPOS Chipper 2X BT, BBPOS WisePOS E, and Stripe Reader M2.

Supported devices: Zenoti supports the following payment terminals and card readers:

  • BBPOS Chipper 2X BT (Stripe) β€” covered in this article
  • BBPOS WisePOS E (Stripe) β€” covered in this article
  • Stripe Reader M2 (Stripe) β€” covered in this article
  • Verifone P400 Plus (Adyen) β€” see the P400 Plus setup article
  • Verifone V400m (Adyen) β€” article in progress
  • Verifone E285 (Adyen) β€” see the Verifone E285 article

A V400m device-specific article is in progress. For setup assistance with that device, contact Zenoti Support.

Audience: Organization administrators, center managers, and front-desk staff responsible for payment hardware setup.


On this page


Before you begin

Permission: Organization administrator access is required to add terminals. Center-level configuration access is required to assign terminals to registers.

  • Your organization must have Stripe Connect configured as the payment processor. See Set up a payment processor.
  • You need physical access to the card reader device and its serial number (printed on the back of the device).
  • For Bluetooth devices (Chipper 2X BT, Stripe Reader M2), you need an iPad (iOS 12 or higher) or Android tablet with Zenoti Mobile installed.
  • Do not manually pair Bluetooth card readers through the device's Bluetooth settings. Pairing must be done through the Zenoti Mobile app. Manual pairing through iOS Settings > Bluetooth makes the device unavailable to Zenoti Mobile.

Pairing rules differ for card readers vs receipt printers. Stripe card readers (Chipper 2X BT, Stripe Reader M2) must NOT be paired via iPad Settings > Bluetooth β€” use Zenoti Mobile in-app pairing only. Bluetooth receipt printers (Star TSP650II, Miura M104) follow the opposite rule: they must be paired via iPad Settings > Bluetooth before Zenoti Mobile can detect them. Mixing the two patterns is the most common peripheral-pairing error. For receipt printer setup, see Pair a receipt printer to your iPad.


Network requirements

Card readers communicate through a combination of local radio links (Bluetooth, WiFi) and outbound internet connectivity to Stripe. If any leg is blocked, the terminal fails either at discovery time or during the first live transaction.

Device Local link Internet egress required from Protocol / port What to whitelist
Chipper 2X BT Bluetooth (iPad) Paired iPad HTTPS 443 to api.stripe.com and *.stripe.com Stripe API domains from the salon WiFi the iPad uses
WisePOS E WiFi (device) WisePOS E device HTTPS 443 to api.stripe.com and *.stripe.com Stripe API domains from the WiFi SSID the WisePOS E joins
WisePOS E Cloud WiFi (device) + Bluetooth/WiFi pairing to iPad Device and iPad HTTPS 443 to api.stripe.com and *.stripe.com Stripe API domains from both networks
Stripe Reader M2 Bluetooth (iPad) Paired iPad HTTPS 443 to api.stripe.com and *.stripe.com Stripe API domains from the salon WiFi the iPad uses
  • All Stripe terminal traffic is HTTPS only. Plain HTTP or custom ports are not supported.
  • For Bluetooth-paired readers, keep the reader within approximately 10 metres / 30 feet of the iPad. Range varies with environmental interference.
  • For WiFi-connected readers, use a 2.4 GHz or 5 GHz network with stable internet. A hotspot from a mobile phone works in a pinch but is not recommended for daily operation.
  • If your IT policy requires endpoint allowlisting rather than domain allowlisting, refer to Stripe's current published IP ranges. These change over time β€” work with your IT team on an automated refresh rather than copying a static list.

External-system prerequisites (Stripe Connect)

The Zenoti terminal flow depends on Stripe Connect being onboarded before any reader is added.

  1. Stripe Connect account. Each center's legal entity must complete Stripe Connect onboarding through Zenoti (Configuration > Payments > Process payments > Payment processor onboarding, Stripe processor row). The merchant application is Stripe-hosted β€” form fields are controlled by Stripe, not Zenoti.
  2. Payout method verified. Stripe must have verified the bank account for payouts before any card reader transaction will settle.
  3. Region. Chipper 2X BT is United States only. WisePOS E and Stripe Reader M2 are available in every Stripe Connect region Zenoti supports (United States, Canada, Australia, United Kingdom, United Arab Emirates). Confirm device-region eligibility in Stripe's terminal hardware catalogue before purchasing.
  4. Physical device purchase. Order terminals through the Zenoti Payments device ordering page, and see the hardware ordering, replacement and return guidance below. A device that was not bought through Zenoti can cause onboarding errors and is not supported.

See Set up a payment processor for the Stripe Connect onboarding walkthrough.


Device comparison

Use the following table to determine which card reader is right for your business:

Feature Chipper 2X BT WisePOS E Stripe Reader M2
Connectivity Bluetooth WiFi Bluetooth
Supported regions USA only All Stripe Connect regions (US, CA, AUS, UK, UAE) All Stripe Connect regions (US, CA, AUS, UK, UAE)
Payment methods Chip insert, swipe, contactless (NFC) Chip insert, swipe, contactless (NFC), PIN Chip insert, swipe, contactless (NFC)
PIN entry No β€” processes only credit cards that do not require PIN Yes β€” supports chip and PIN transactions No
Debit cards Only if the card allows credit transactions without PIN Yes, including PIN-required debit Only if the card allows credit transactions without PIN
Device type Handheld, battery-powered Countertop, Android-based with touchscreen Handheld, battery-powered
Mirror mode Yes (via iPad) Yes (via WiFi or Cloud) Yes (via iPad)
On-device tip prompts No Yes Yes
Save card for future use Yes Yes Yes
Firmware updates Via Zenoti Mobile Via Zenoti Mobile or device admin Via Zenoti Mobile
Power Battery with USB charging; can be used while charging USB adaptor (sold separately) Battery with USB-C charging

Note: The Chipper 2X BT is available only in the United States. If your business operates in other countries, use WisePOS E or Stripe Reader M2.

Verifone P400 and P400 Plus: Stripe no longer supports payments on the Verifone P400. Only the Verifone P400 Plus is supported. If the add-terminal list shows only P400 Plus and your center still uses the older P400, upgrade to the P400 Plus. See Verifone P400 Plus.


Set up Chipper 2X BT

The BBPOS Chipper 2X BT is a handheld, Bluetooth-connected card reader for mobile payment collection. It supports chip insert, swipe, and contactless (NFC) payments from credit cards that do not require a PIN.

Limitations

  • Supported in the USA only.
  • Cannot process payments from cards that require a PIN.
  • Can process debit card payments only if the debit card allows credit transactions without PIN.
  • Connects to only one iPad at a time.

Add the terminal in Zenoti

  1. Navigate to Configuration > Payments > Process payments > Payment processor onboarding.

  2. Under Payment Processors, open the Stripe processor row (Setup for a processor that is not configured yet, Change for one that is) and select the Terminals tab.

  3. Add a terminal.

  4. Enter the following details:

    Field Source What to enter
    Terminal Name Zenoti administrator (you choose) A descriptive name (for example, "Chipper BT - Front Desk"). Appears in the terminal list on Zenoti web and in Zenoti Mobile.
    Serial Number Physical label on the back of the card reader The serial number printed on the back of the device. Do not copy a sample value from another reader.
  5. Click Add.

  6. Click Save.

Connect via Zenoti Mobile (Bluetooth)

  1. On the iPad, enable Location Services for Zenoti Mobile. Go to iPad Settings > Zenoti Mobile > Location and select Always.
  2. Open the Zenoti Mobile app and tap Settings > Connected Card Readers.
  3. Tap Search. Zenoti Mobile discovers card readers within Bluetooth range and displays them with their terminal name and serial number.
  4. Tap Connect next to your device.
  5. When prompted to enable auto-connection, tap Yes. Auto-connection allows Zenoti Mobile to reconnect to this reader automatically when the app launches.

The card reader is now ready for payment collection.

Collect a payment

  1. Press the power button to wake the card reader if it is in sleep mode. A blue light indicates the reader is on.
  2. On the iPad, open Zenoti Mobile and select the appointment for payment.
  3. Tap Proceed for Payment.
  4. Select Use Card Reader as the payment method.
  5. Select your Chipper 2X BT reader from the list.
  6. Optionally, select Save card for future use to store the card details for the guest.
  7. Tap Collect.
  8. The guest inserts the chip, swipes, or taps their card on the reader.
  9. If signature capture is enabled, the guest signs on the iPad screen.
  10. The payment confirmation screen appears.

Firmware updates

Stripe periodically releases firmware updates for the Chipper 2X BT. To check for and install updates:

  1. Open Zenoti Mobile and tap Settings > Connected Card Readers.
  2. Tap the info icon next to the connected device.
  3. Tap Check for update.
  4. If an update is available, tap Install update. Do not disconnect the reader during the update.

Tip: A red badge on the Settings icon and a red exclamation mark on Connected Card Readers indicate that a firmware update is available.

Battery and charging

The Chipper 2X BT is battery-powered and charges via USB. You can use the device while it is charging. The LED indicator beside the power button shows the device status β€” refer to the BBPOS Chipper 2X BT User Guide on the Stripe Docs site for detailed LED status codes and battery life specifications.

Disconnect the card reader

  1. Tap Settings > Connected Card Readers in Zenoti Mobile.
  2. Tap the info icon next to the connected device.
  3. Tap Disconnect the card reader.

You can now connect a different reader.

Troubleshooting

Bluetooth scan timeout error

This error occurs if:

  • The card reader is not powered on or is out of Bluetooth range. Solution: Press the power button, wait a few seconds, and tap Retry.
  • The serial number in terminal settings does not match the physical device. Solution: Verify the serial number on the back of the reader matches what was entered in Zenoti.
  • The reader is connected to a different iPad. Solution: Disconnect from the other iPad first. A reader connects to only one iPad at a time.
  • Location services are not enabled. Solution: Go to iPad Settings > Zenoti Mobile > Location and select Always.

Unable to process payments

If none of the above solutions work, you can:

  • Switch to a Verifone or WisePOS E terminal to complete the payment.
  • Process the card payment manually through the desktop POS (Point of Sale).

Device paired through iOS Bluetooth settings

If you manually paired the reader through iOS Settings > Bluetooth, it will not work with Zenoti Mobile. Unpair the device from iOS Bluetooth settings and reconnect through Zenoti Mobile > Settings > Connected Card Readers.

FAQ

Can a guest enter a PIN on the Chipper 2X BT? No. The Chipper 2X BT processes only credit cards that do not require a PIN.

Can I process debit card payments? Only if the debit card allows credit transactions without requiring a PIN.

Can I connect the reader to multiple iPads? No. The Chipper 2X BT connects to only one iPad at a time. To use it with a different iPad, disconnect from the current one first.

Can I use the device while it is charging? Yes. The Chipper 2X BT can process payments while connected to USB power.


Set up WisePOS E

The BBPOS WisePOS E is a countertop, Android-based card reader with a touchscreen. It supports chip insert, swipe, contactless (NFC), and PIN transactions, and connects via WiFi.

Supported regions

WisePOS E is available in all Stripe Connect regions: United States, Canada, Australia, United Kingdom, and UAE.

Device model selection

When adding the terminal in Zenoti, select the correct device model:

  • BBPOS WisePOS E β€” If the device connects directly to your computer or network (WiFi, direct registration).
  • BBPOS WisePOS E Cloud β€” If the device is used with Zenoti Mobile on an iPad (cloud-registered).

Add the terminal in Zenoti

  1. Navigate to Configuration > Payments > Process payments > Payment processor onboarding.

  2. Under Payment Processors, open the Stripe processor row (Setup for a processor that is not configured yet, Change for one that is) and select the Terminals tab.

  3. Add a terminal.

  4. Choose the device model.

  5. Enter the following details:

    Field Source What to enter
    Device Model Zenoti drop-down (you choose) BBPOS WisePOS E for direct WiFi registration, or BBPOS WisePOS E Cloud for iPad-via-Zenoti Mobile setup.
    Terminal Name Zenoti administrator (you choose) A descriptive name (for example, "WisePOS E - Register 1").
    Registration Code Generated on the WisePOS E device itself A short pairing code displayed by the device. See steps below.

To obtain the registration code:

  1. On the WisePOS E, open Settings > Device Settings.
  2. Enter the code 07139.
  3. Tap Generate Registration Code. The device displays its registration code.
  4. Enter the generated code in the Zenoti Payments terminal setup.
  5. Click Add.

Connect WisePOS E to WiFi

  1. Turn on the device and wait for the home screen.
  2. Swipe right from the left edge of the home screen to open the settings panel.
  3. Tap Settings and enter the code 07139 when prompted.
  4. Select WiFi Settings > Add a Network.
  5. Select your network and enter the password.

The device is now connected to the internet and ready for payment processing.

Set up the WisePOS E away from the shop

You can set up the WisePOS E at home or another location and bring it to the shop later. It must be connected to the shop's network before it processes payments. The POS and the terminal must be on the same network. If the terminal does not connect even though the network is saved, forget the network on the device, restart the terminal, and reconnect with the correct password.

Payment methods

WisePOS E supports all major payment methods:

  • Chip insert β€” The guest inserts the card into the chip slot.
  • Contactless (NFC) β€” The guest taps the card or mobile wallet on the reader.
  • Swipe β€” The guest swipes the card through the magnetic stripe reader.
  • PIN entry β€” For cards that require a PIN, the guest enters it on the touchscreen.

On-device tip prompts

WisePOS E supports tip prompts directly on the device screen. To configure tips, see Configure tips on terminals.

Important: Terminal firmware must be updated before tip prompts will function. See Set up hardware peripherals for firmware update steps.

Charging

WisePOS E is a countertop device powered by a USB adaptor (sold separately). Plug the device into a wall socket or outlet using the USB adaptor for continuous operation.

Troubleshooting

How do I navigate to the device settings?

Swipe right from the home screen. Tap Settings and enter the code 07139.

How do I remove the backplate?

Refer to the quick-start guide included with your device for backplate removal instructions.

WiFi connection drops during payment

If the WiFi connection drops during a transaction, the device displays a connection error. Verify the device is within range of your WiFi network and the network is stable. Reconnect via Settings > WiFi Settings if needed.

FAQ

Is WisePOS E available outside the USA? Yes. WisePOS E is available in all Stripe Connect regions: US, Canada, Australia, UK, and UAE.

What is the difference between WisePOS E and WisePOS E Cloud? WisePOS E connects directly via WiFi. WisePOS E Cloud is cloud-registered and used with Zenoti Mobile on an iPad. Select the correct model when adding the terminal in Zenoti.

Does WisePOS E support PIN transactions? Yes. Guests can enter a PIN on the touchscreen for cards that require it.


Set up Stripe Reader M2

The Stripe Reader M2 is a handheld, battery-powered card reader that connects via Bluetooth. It supports chip insert, contactless (NFC), and swipe payments.

Important: The Stripe Reader M2 connects by Bluetooth, not WiFi, so it cannot be used from a desktop computer. Pair it with an iPad or another mobile device running Zenoti Mobile, and start the payment from that device. It pairs with only one iPad at a time. Disconnect it from any other iPad before you pair it with a new one. Pair it in Zenoti Mobile (Settings > Connected Card Readers > Discover Stripe M2), not in the iPad's own Bluetooth settings.

Supported regions

Stripe Reader M2 is available in all Stripe Connect regions: United States, Canada, Australia, United Kingdom, and UAE.

Add the terminal in Zenoti

  1. Navigate to Configuration > Payments > Process payments > Payment processor onboarding.

  2. Under Payment Processors, open the Stripe processor row (Setup for a processor that is not configured yet, Change for one that is) and select the Terminals tab.

  3. Add a terminal.

  4. Enter the following details:

    Field Source What to enter
    Device Model Zenoti drop-down (you choose) Stripe Reader M2.
    Terminal Name Zenoti administrator (you choose) A descriptive name. Use a unique name to identify the device if you have multiple readers.
    Serial No Physical label on the back of the device The serial number printed on the back of the Stripe Reader M2.
  5. Click Add.

Connect via Zenoti Mobile (Bluetooth)

  1. Open the Zenoti Mobile app.
  2. Navigate to Settings > Connected Card Readers > tap Discover Stripe M2.
  3. Ensure the Stripe Reader M2 is powered on and placed near your mobile device.
  4. Zenoti Mobile discovers and connects to the reader.

After the connection is established, you can start collecting payments.

Collect a payment

  1. On the iPad or Android tablet, open Zenoti Mobile and select the appointment for payment.
  2. Tap Proceed for Payment.
  3. Select Use Card Reader as the payment method.
  4. Select the Stripe Reader M2 from the list.
  5. Optionally, select Save card for future use to store the card details for the guest.
  6. Tap Collect.
  7. The guest inserts the chip, swipes, or taps their card on the reader.
  8. The payment confirmation screen appears.

On-device tip prompts

Stripe Reader M2 supports tip prompts. To configure tips, see Configure tips on terminals.

Important: Terminal firmware must be updated before tip prompts will function. See Set up hardware peripherals for firmware update steps.

Firmware updates

To check for and install firmware updates:

  1. Open Zenoti Mobile and tap Settings > Connected Card Readers.
  2. Tap the info icon next to the connected device.
  3. Tap Check for update.
  4. If an update is available, tap Install update. Do not disconnect the reader during the update.

Battery and charging

Stripe Reader M2 is battery-powered and charges via USB-C. You can use the device while it is charging. For detailed battery life specifications, refer to Stripe's terminal documentation.

Troubleshooting

Reader not discovered

  • Ensure the reader is powered on and within Bluetooth range.
  • Ensure Location Services and Bluetooth are enabled on your device.
  • Restart the Zenoti Mobile app and try again.

Reader disconnects during payment

If the reader disconnects mid-transaction, Zenoti Mobile displays a notification. Power cycle the reader (turn off and back on), then reconnect from Settings > Connected Card Readers and retry the payment.

If the far left and far right lights blink rapidly (about every 0.1 second), the reader may have been tampered with or is defective. Before you ask for a replacement:

  1. Charge the reader fully.
  2. In Zenoti Mobile, go to Settings > Connected Card Readers > Discover Stripe M2 and reconnect.
  3. Confirm the serial number in the terminal settings matches the number on the device.
  4. On the iPad, go to Settings > Zenoti Mobile > Location and select Always.

If the lights keep blinking, the reader needs to be replaced. Follow Request a replacement terminal and have the reader's serial number ready.

Unable to process payments

If the reader repeatedly fails to process payments:

  • Check for firmware updates and install if available.
  • Ensure the reader is charged (connect to USB-C power).
  • Try using a different card to rule out card-specific issues.
  • If the issue persists, switch to a WisePOS E or Verifone terminal, or process the payment manually.

FAQ

Does Stripe Reader M2 support mirror mode? Yes. Mirror mode works with the Stripe Reader M2 the same way it works with Chipper 2X BT β€” via Bluetooth connection to an iPad.

Does Stripe Reader M2 support PIN entry? No. Stripe Reader M2 does not have a PIN entry interface.

Is Stripe Reader M2 available outside the USA? Yes. It is available in all Stripe Connect regions: US, Canada, Australia, UK, and UAE.

Can I save a card for future use with Stripe Reader M2? Yes. Select Save card for future use when collecting a payment.

Does Stripe Reader M2 work on Android? Yes. Stripe Reader M2 connects via Bluetooth to both iOS and Android devices with Zenoti Mobile installed.


Mirror mode with card readers

Mirror mode turns a second device (typically an iPad) into a customer-facing display during checkout. All Stripe terminal card readers supported by Zenoti work with mirror mode:

Card Reader Mirror Mode Connection Method
Chipper 2X BT Yes Bluetooth (via iPad)
WisePOS E Yes WiFi (direct)
WisePOS E Cloud Yes WiFi (cloud, via iPad)
Stripe Reader M2 Yes Bluetooth (via iPad)

For complete mirror mode setup instructions, see Use mirror mode.


Handle transaction failures

Every Stripe terminal failure falls into one of the modes below. Zenoti does not auto-retry mid-transaction β€” no charge is applied when a transaction fails, and the front-desk operator must either retry on the same reader, fall back to another reader, or process the payment manually.

Failure mode User-visible symptom Affected device(s) Resolution
Card declined POS or Zenoti Mobile shows the decline reason returned by the card network All Ask the guest for another card, use a card saved on the guest profile, or process manually. The decline is issuer-driven; a second tap on the same card will usually produce the same result.
Bluetooth disconnection Zenoti Mobile shows a disconnection notification Chipper 2X BT, Stripe Reader M2 Press the power button to wake the reader, keep it within 10 m / 30 ft of the iPad, then go to Settings > Connected Card Readers and reconnect. Retry the payment.
WiFi disconnection Device screen shows a connection error WisePOS E Verify the WiFi network is reachable, then reconnect via device Settings > WiFi Settings. Retry the payment.
Timeout communicating with Stripe Terminal reports a timeout and aborts the transaction All Check signal strength (Bluetooth range, WiFi signal), battery level, and internet connectivity. Move the reader closer to the iPad or access point, or plug in for power, then retry.
Firmware update required Zenoti Mobile or the device prompts for an update; tips or signature capture are unavailable All Install the pending firmware update (see the firmware section for the relevant device). Do not process payments during the update.
Reader not discovered Search returns no results in Zenoti Mobile Chipper 2X BT, Stripe Reader M2 Confirm the serial number entered in Zenoti matches the label on the device, ensure Location Services and Bluetooth are on, and confirm the reader is not already paired with a different iPad.
Wrong admin code on WisePOS E Device rejects the admin code when entering Settings WisePOS E Admin codes are vendor-controlled; do not share them in help documentation. Contact your Stripe account representative for the current code, then change it after initial setup.

Apply updated surcharge or payment-fee configuration

After you save a change to a surcharge or payment-fee configuration on a payment terminal, the terminal must load the updated settings before the new configuration takes effect. The terminal does not apply configuration changes automatically at the moment you click Save in Zenoti.

To activate the new configuration, use either of the following approaches:

Restart the terminal

Restart the terminal once. On reboot, the terminal retrieves and applies the latest configuration from Zenoti. No additional steps are required after the restart.

Apply from the terminal's Settings screen

As an alternative to a full restart, you can apply the update directly from the terminal:

  1. Access the terminal's Settings screen (method varies by device β€” see the device-specific setup section above for how to reach the admin menu on your model).
  2. Select the option to apply or refresh the configuration.

The updated surcharge or payment-fee settings take effect immediately.

Note: If the terminal reports that it is already up to date when you check for a software update, this is correct β€” the terminal has the current software version. The restart (or Settings-screen apply step) is what activates the new configuration, not a software update. No additional software download is required.


Enable signature collection on POS

  1. Navigate to Configuration > Payments > Process payments > Payment processor onboarding.
  2. Expand the configured payment processor by clicking its arrow. The Payment Options section appears only after you expand the processor.
  3. Under Payment Options, select Enable signature collection on POS.
  4. Save the settings.

Device limitation: Signature capture is available on the Stripe Reader M2 only. It is not available on the WisePOS E or myZen Tap on Mobile.


Board a terminal (general)

The following boarding flow applies to terminals that require an on-device boarding step (such as Adyen-certified terminals). Stripe-paired readers (Chipper 2X BT, WisePOS E, Stripe Reader M2) use the Zenoti registration/pairing flow described in their respective sections above.

  1. Ensure the terminal is connected to WiFi (use the device WiFi settings, not Zenoti).
  2. On the terminal, tap Board the Terminal.
  3. The terminal displays your center's registered address. Confirm it is correct, then confirm.
  4. The terminal reboots automatically β€” this is expected.
  5. After reboot, the terminal is ready for use in Zenoti.

If the store address shown during boarding is incorrect, do not confirm. Contact Zenoti Support to update the address before boarding. Boarding with an incorrect address may cause settlement issues.


Troubleshoot POI errors (all terminals)

"POI" (Point of Interaction) in error messages refers to the payment terminal. When a POI error appears:

  1. Check battery/power β€” ensure the device is charged or plugged in.
  2. Check internet connectivity β€” verify the WiFi icon is active or the Ethernet cable is connected.
  3. Access the terminal admin menu (method varies by device β€” see the device-specific article).
    • Verifone P400 Plus: Press 9 + green Enter key, then enter PIN 4060.
  4. Navigate to Network > WiFi > Add Network if connectivity is lost.
  5. If an update is running: Software > Update takes 30–40 minutes and blocks transactions during that window. Wait for the update to complete before processing payments.
  6. Reboot via admin menu: Reboot.

If the POI error persists after these steps, contact Zenoti Support with the error code and device model.


Replace a lost or stolen terminal

  1. Confirm that KYC (Know Your Customer) verification is fully cleared for the center.
  2. Find the serial number on the label on the back of the device. Check it carefully before you enter it.
  3. Navigate to Configuration > Payments > Process payments > Payment processor onboarding > Terminals and add the terminal.

If the serial number does not match, contact Zenoti Support with the serial number and the device model.


Order, replace and return terminals

Order a terminal

Order terminals through the Zenoti Payments device ordering page (North America): go.zenoti.com/zenoti-payments-na-device/brand-selection.html.

  1. Confirm the location, the terminal model and the supported payment processor before you order.
  2. Place the order and keep the order confirmation. You need it for tracking and onboarding.

Note: A device that was not bought through Zenoti may cause onboarding errors and is not supported.

Request a replacement terminal

  1. Try remote troubleshooting first, using the steps earlier in this article.
  2. If the problem remains, contact Zenoti Support and provide:
    • the receiver's full name, phone number and email address
    • the full delivery address, including the postcode or pin code
    • the terminal serial number and model
    • a short description of the problem
  3. A return label for the faulty device is included with the replacement shipment.

If the return label does not arrive, contact Zenoti Support for a new one. Give the serial number and model of each device you are returning. An additional device is not added to the same return unless Zenoti Support confirms that the label covers more than one item.

Track an order or replacement

The tracking number for an order is in the shipping confirmation email. If you have none yet, confirm that the order was processed and contact Zenoti Support with the order reference or the location details. For a replacement shipment, the carrier tracking number is shared once the shipment is dispatched.

Terminal does not charge

If a Castle S1F2 or other terminal does not charge, try a different USB-C cable first. If the terminal charges with the other cable, Zenoti Support sends a replacement cable. If it still does not charge, the terminal itself is replaced. In both cases, contact Zenoti Support with the receiver details listed above.

Was this article helpful?
Your feedback helps us improve our documentation.